CR9922
3 Band Dual Alarm
Clock Radio
Please read this manual before use
Controls
15
16
17
18
19
20
21
18. Volume control
15. Display brightness switch
16. Alarm selector switch
17. Function switch
19. Waveband selector
20. Tuning control
21. Battery compartment (on underside)
If you need any further advice, please call our Technical Helpline on :-
02087580338(Mon-Fri)
2
Switching on and setting the time
ON
Before using your clock radio you must first set the correct time.
1. Place the unit on a flat surface. Plug the mains lead into a wall socket
and switch on.
2. The clock display will flash 12:00.
3. Press and hold down the Time Set button.
4. WhilstholdingdowntheTimeSetbuttonpressthefastforward(Fast),
or slow reverse (Slow) buttons to set the time. Release the buttons
whenthecorrecttimeisreached.Theclockusesa12hourdisplaywith
a PM indicator. Ensure that the correct 12 hour cycle is selected.
3
Listening to the Radio
1. Switch on the radio by sliding the Function switch to the 'On'
position. The LED dial pointer will light up indicating that the radio
is switched on.
2. SelecttherequiredwavebandusingtheWavebandselectorswitch.
3. Tune in to the desired station by rotating the Tuning control. The
station frequency is indicated by the LED dial pointer.
The Wire aerial located on the rear of your clock radio is for FM
reception. The wire should be fully extended and positioned for
optimumreception.
For MW and LW reception there is a built in ferrite aerial. Rotate your
clock radio to the position giving best reception.
4. Adjust the volume by rotating the Volume control.
5. The radio can be switched off by sliding the Function switch to the
'Off' position.
Note:iftheradiodoesnotswitchoff,thismaybecausedbyinadvertent
operationoftheSleepbutton. PresstheAlarm/Offbuttontocancel.
If you need any further advice, please call our Technical Helpline on :-
02087580338(Mon-Fri)
4
Setting alarm times
The alarms can be set to wake you by either buzzer or the radio alarms.
Your alarm clock radio has 2 separate alarms which can be set to
activate at different times.
Setting alarm 1
1. Slide the Alarm function switch to the '
' position.
1
2. Press and hold down the Alarm set button.
3. Whilst holding down the Alarm Set button press the fast forward
(Fast), or slow reverse (Slow) buttons to set the required alarm time.
Releasethebuttonswhenthecorrectalarmtimeisreached.Theclock
uses a 12 hour display with a PM indicator. Ensure that the correct
12 hour cycle is selected.
Setting alarm 2
1. Slide the Alarm function switch to the '
' position.
2
2. Press and hold down the Alarm set button.
5
3. Whilst holding down the Alarm Set button press the fast forward
(Fast) or slow reverse (Slow) buttons to set the required alarm time.
Releasethebuttonswhenthecorrectalarmtimeisreached.Theclock
uses a 12 hour display with a PM indicator. Ensure that the correct
12 hour cycle is selected.
Checking the Alarm Times
1. To check alarm 1 time, set the Alarm function switch to the '
'
1
position.
2. Press the Alarm Set button to display the alarm 1 time.
3. To check alarm 2 time, set the Alarm function switch to the '
'
2
position.
4. Press the Alarm Set button to display the alarm 2 time.
Note: The alarm times cannot be checked if the Alarm function
switch is in the ' ' position.
1+2
If you need any further advice, please call our Technical Helpline on :-
02087580338(Mon-Fri)
6
Setting the alarms to wake to buzzer
1. Set the alarm time as previously described. Set the Function
switch to the 'Buzz' position. Set the Alarm selector switch to
the
'
', '
1
' or '
' position. The corresponding Alarm
1+2
2
indicators will light.
2. The buzzer alarm will sound every day at the preset time for 59
minutes. To turn off the alarm until the next day press the Alarm/
Off button. To turn off the alarms permanently set the Function
switch to the 'Off' position.
Note: If an alarm time has not been set and the Function switch is
left in the 'Buzz' or 'Radio' position, the buzzer or radio alarms will
operate at 12:00 midnight. If you do not require the alarm function,
ensure that the Function switch is set to the 'Off' position.
Setting the alarms to wake to radio
1. Set the alarm time as previously described. Set the Function
switch to the 'Radio' position. Set the Alarm selector switch to the
'
', '
1
'or'
'position. ThecorrespondingAlarmindicators
1+2
2
will light. Ensure that a station is tuned in and the Volume control
is set to the required level.
2. The radio alarm will operate every day at the preset time for 59
minutes. To turn off the radio alarm until the next day press the
Alarm/Off button. To turn off the alarms permanently set the
Function switch to the 'Off' position.
Note: If an alarm time has not been set and the Function switch is
left in the 'Buzz' or 'Radio' position, the buzzer or radio alarms will
operate at 12:00 midnight. If you do not require the alarm function,
ensure that the Function switch is set to the 'Off' position.
7
Snooze control
The buzzer or radio alarm can be silenced for 7 minutes by pressing the
Snooze button. This sequence can be repeated whilst the alarm is
sounding.
Sleep timer
The radio can be set to switch off after a preset time has elapsed.
Press and hold down the Sleep button until the desired time is reached
(maximum 59 minutes in 1 minute steps). The radio will switch off after
the sleep time has elapsed.
To cancel the sleep function before the preset time has expired, press
the Alarm/Off button.
AutoDimmer
The Auto Dimmer located on the bottom right side of the LED display will
automatically adjust the intensity of the clock display to suit room
brightness. The display brightness can be further adjusted using the
Display dimmer switch located on the left side of your clock radio.
Headphones (on rear)
AHeadphoneSocket(3.5mm)isprovidedforusewitheitherheadphones
oranearpiece.Insertingaplugautomaticallymutestheinternalloudspeaker.
If you need any further advice, please call our Technical Helpline on :-
02087580338(Mon-Fri)
8
General
Fuse
Do not allow this unit to be exposed to water or steam. It is recommended
that the FM band be used wherever possible as better results in terms
of quality and freedom from interference will usually be obtained than
on the MW or LW bands.
This apparatus must be protected by a 3A fuse (BS1362) in a 13A plug
(BS1363). If another type of plug is used a 5A fuse should be fitted in the
plug, adaptor or distribution board.
IF IN DOUBT - CONSULT A QUALIFIED ELECTRICIAN.
Mainssupply
Back-upBattery(notnecessaryfortheunittofunction)
The CR9922 will operate from a supply of AC 230volts, 50Hz
only.
Slide the battery cover catch in the direction of the arrow. Remove the
batterycover.Fita9voltIECsize6LR61(6F22,PP3)orequivalentbattery
into the compartment. Replace the battery cover.
For your convenience this product is supplied with a plug which is fitted
with a fuse of the appropriate rating. If the plug supplied is not suitable
for your socket outlet, it should be removed by unscrewing the plug top,
the terminal screws, and removing the cable.
Thetimeandalarmsettingswillberetainedduringatemporaryfailureofthe
ACmainssupply. TheLEDdisplaywillnotbeoperational. Thedisplaywill
be extinguished to conserve battery life, but the memory will retain details
of the time and alarm time settings.
The correct style of plug to suit your household together with a correctly
rated fuse should be fitted.
If your clock radio is not to be used for a prolonged period of time, remove
the battery to avoid damage by battery leakage.
IFINDOUBT-CONSULTAQUALIFIEDELECTRICIAN
IMPORTANT. DO NOT make any connection to the larger terminal which
is marked with the letter E or by the safety earth symbol
Green or Green-and-yellow.
or coloured
(Underside)
The wires in the mains lead are coloured in accordance with the
following codes :-
BLUE - NEUTRAL
BROWN - LIVE
As these colours may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows:-
The wire coloured BLUE must be
connected to the terminal marked N
E(Earth)
or coloured BLACK.
Brown(Live)
3 amp
The wire coloured BROWN must be
connected to the terminal marked L
or coloured RED.
L
Blue (Neutral)
N
Mains Lead
9
Specifications
Power Requirements
Mains
Circuit Features
Loudspeaker
8 ohms
AC 230 volts, 50Hz
only
Outputpower350mW
Back-up Battery
IEC size 6LR61 (6F22, PP3)
Aerial System
FM
Wire Aerial
Frequency Coverage
FM
87.5 - 108MHz
525 - 1610kHz
150 - 260kHz
MW
LW
Built-in Ferrite aerial
Built-in Ferrite aerial
MW
LW
ROBERTSRADIOLIMITED
PO BOX 130
MEXBOROUGH
SOUTH YORKSHIRE
S64 8YT
The Company reserves the right to amend the specification without notice.
If you need any further advice, please call our Technical Helpline on :-
02087580338(Mon-Fri)
10
Guarantee
This radio is guaranteed for twelve months from the date of delivery to the original owner against failure due to faulty workmanship or component
breakdown, subject to the procedure stated below. Should any component or part fail during this guarantee period it will be repaired or replaced
free of charge.
The guarantee does not cover:
1. Damage resulting from incorrect use.
2. Consequential damage.
3. Product with removed or defaced serial numbers.
Procedure: Any claim under this guarantee should be made through the dealer from whom the instrument was purchased. It is likely that your Roberts'
dealer will be able to attend to any defect quickly and efficiently but should it be necessary the dealer will return the instrument to the company’s
service department for attention. In the event that it is not possible to return the instrument to the Roberts' dealer from whom it was purchased,
please contact Roberts Radio service department at the address shown on the rear of this manual before taking further action.
These statements do not affect the statutory rights of a consumer.
ROBERTS RADIO TECHNICAL SERVICES DEPARTMENT
97-99WortonRoad
IsleworthMiddlesex
TW76EG
Technical Helpline:- 020 8758 0338 (Mon-Fri)
Issue 1
|